Trimming Tools
Stiction (noun): the friction which tends to prevent stationary surfaces from being set in motion.
Adjusting zenith can be frustrating due to the stiction between the mounting screws and the headshell. Even brass washers can grab and go, making it difficult to make small zenith adjustments.
Building on our experience with our Schröder headshell tuning kit, we decided to adapt some nylon washers for use in a Kuzma headshell.
With the majority of headshells, a simple washer substitution can be made.
Note however, the reinforcement ribs in Kuzma headshells require using either small diameter washers, or filing flats on to larger washers.
Washers small enough to fit between the ribs are barely larger then the diameter of socket head mounting bolts, so this doesn't do much to help the cartridge slide easily during adjustment.
We prefer filing flats onto washers, to increase the sliding contact area.
Shown here, are brass washers we generally use for the final installation with Kuzmas (although we're open to cartridges which favor nylon).
Custom Brass Washers
As noted above, we adapted nylon washers for smoother operation during the setup process.
After setup, we'll audition all three washer combinations to see which variation works for the particular tonearm and cartridge:
To swap out the washers without disturbing the geometry, remove/replace one screw at a time.
Make sure to adjust the torque after you've completed this. We've found that most people over torque their cartridges which can compromise dynamics and introduce distortion.
Over-torquing induces mechanical stresses on the cartridge body.
In general, the screws should be barely tighter than that which is required to keep the cartridge from moving in the headshell.
Experiment with this if you don't believe us.
We won't tell you which combination worked for this Kuzma arm/Kuzma cartridge combination because not only will it ruin your fun, but these solutions are system-specific: influenced by both your arm and cartridge as well as likely everything downstream of it.
While our general findings favor brass and stainless, the Schröder CB's energy management strategy is one notable exception, so have fun with this and feel free to talk to us about your observations.
2 Nylon Washers
1 Nylon & 1 Brass
2 Brass Washers
Related Posts
click to expandWith apologies to Wayne Gretzky …Wayne Gretzky was quoted as saying: “you miss 100% of the shots you don’t take”. With respect to cleaning machines, the best machine is the machine you actually use.I’m reminded of cameras, where a similar rule applies: it doesn’t matter how good your camera is if your rig is
Read More(click to enlarge)Shipping a mounted Van den Hul …Preparing a mounted Van den Hul cartridge for shipping is not for the faint of heart.We recently prepared a Van den Hul Colibri XGW Signature Stradivarius, and these photos are the result.In a perfect world, cartridges would have stylus guards that actually work, but other design considerations
Read More5-pin DIN ConnectorThat, is the question … For years, we bought into the common knowledge that tonearms wired with a straight run from the cartridge clips to the connectors (RCA or XLR) are superior to arms with plug-in cables employing a 5-pin DIN connector. Then, we put the theory to the test. The ExperimentWe compared two 4Point, 11″
Read MoreWind RiverCan we talk? Quite some time ago, we published photos of a well-maintained stylus, and followed up with a post describing various stylus cleaning methods. It’s time to have a serious conversation about our connectors …Audio HygieneMaintaining a high-performing audio system requires a minimal amount of work, and one chore involves periodically cleaning and re-treating our
Read MoreNever miss a good story!
Subscribe to our newsletter to receive a sample setup report we created for a customer.
Subscribers also receive discounts on all accessories, including Audiodesk, Feickert and AnalogMagik.
This report is in 3 sections:
Documentation of the customers's setup and QC
30 pages packed with general setup information - tricks you may not have seen before
An appendix with a guide to tools and other setup tips, including how build your own azimuth gauge
Click the photo below, to subscribe.